Product Search
Search results for 'D6931'
Showing 41 - 61 of 562 Total Results
(4) options
Location: Manual Compression Testing Machines
Testing range of 4,000 to 400,000 lbs. (17.8 – 1,780 kN) with an accuracy of ±.5% of indicated load., Rigid heavy duty load frame design. . Request a Quote Designed to meet the demands of production testing programs where day to day performance is required. Its heavy duty load frame features...
SA-0240
Location: Pocket Penetrometer
The Soil Pocket Penetrometer from Test Mark is used for the evaluation and classification of cohesive soils in terms of soil consistency.
CA-2900
Location: Cube Molds
Cement Cube Sand from Test Mark is used for preparing hydraulic cement mortars for 2-inch (51 mm) cube compression testing.
(2) options
Location: Portable Curing Boxes
Portable Curing Boxes for concrete testing store up to 22 standard 6x12 test cylinders from Test Mark Industries.
CA-1510
Location: Shakers, Gilson
Test Mark provides Gilson sieve shakers for 8-inch and 12-inch sieves.
(2) options
Location: Sample Bags
Plastic-lined sample bags from Test Mark are used to transport soils, cement, aggregate, and wet materials from the field to the laboratory.
(2) options
Location: Vebe Consistometer
The Vebe Consistometer determines the consistency and density of low slump roller-compacted concrete - from Test Mark Industries.
(2) options
Location: Rebar Locator
Test Mark's Rebarscope™ locates reinforcement bars in concrete and determines their depth and size.
(3) options
Location: Vertical Cappers
Test Mark's heavy-duty vertical cappers are used to apply molten capping compound to the ends of concrete cylinders for compression testing and insure the testing forces will be evenly distributed over the ends of the test cylinder.
(4) options
Location: Test Platens
Test both cubes and cylinders . Used for testing 2” (50 mm) cubes and 3” (76 mm) diameter cylinders and cores in compression. Cube test set consists of a spherically seated platen assembly and a lower pedestal used for positioning the cube sample at the correct height for testing. The bearing block...
AA-0068
Location: Vacuum Pycnometer (Rice Test)
The vacuum pycnometer from Test Mark is used for determining the maximum specific gravity of bituminous paving mixtures with a maximum aggregate size up to 3/4-inch and a 2,000 g capacity.
Dynamic Cone Penetrometer with Auger
SA-1200
Location: Dynamic Cone Penetrometer
Test Mark's Dynamic Cone Penetrometer (DCP) uses a 15 lb. steel mass that falls 20 inches and can be used effectively in augered holes to depths of 15 to 20 feet.
CA-0470
Location: Rubber Mallet
The rubber mallet from Test Mark is used to consolidate materials and release entrapped air in concrete molds, air meters, slump cones and unit weight buckets.
CA-1400
Location: Lab Ovens
These gravity convection ovens are used for drying, baking, sterilizing, evaporating, heat-treating, and testing. 0.7 cu. ft. model.
CA-1405
Location: Lab Ovens
These gravity convection ovens are used for drying, baking, sterilizing, evaporating, heat-treating, and testing. 1.27 cu. ft. model.
CA-1410
Location: Lab Ovens
These gravity convection laboratory ovens are used for drying, baking, sterilizing, evaporating, heat-treating, and testing. 2.0 cu. ft. model.
(4) options
Location: Manual Compression Testing Machines
Testing range of 5,000 to 500,000 lbs. (22.2 – 2,224 kN) with an accuracy of ±.5% of indicated load., Frame stiffness rating of 41.6 million lbs/in., Easier specimen loading with large platen table. . Request a Quote Our CM-5000 series machines feature rigid distortion-resistant load frames...
CA-0610
Location: Air Entrainment/Roll-A-Meter
The lightweight aluminum Roll-A-Meter is used to determine the air content of concrete mixes, and is recommended for concrete containing lightweight aggregates, air-cooled slag or highly porous aggregates.
AA-0050
Location: Asphalt
Circular, smooth-edged 4" diameter disc fits in bottom of 4" compaction molds prior to compaction test. Facilitates removal of sample specimen from mold.